Hydro jetting is the gold standard for cleaning drain and sewer lines that a cable machine can't fully restore. A specialized hose delivers water at 1,500 to 4,000 PSI through forward and reverse nozzles, scouring the pipe wall back to full diameter. It cuts through grease, soap scum, mineral scale and even tree roots — leaving a line that flows like new instead of just punching a hole through the clog.
We carry truck-mounted jetters sized for residential and small-commercial lines across North Atlanta. Every hydro-jet job starts with a sewer-camera inspection so we know what we're actually dealing with, and ends with a second camera pass to verify the line is clean. Same-day service and flat-rate pricing. (As with any drain cleaning, the work itself is not warrantied — industry standard, since what comes back down the line afterward is outside our control.)
When hydro jetting is the right call
A cable machine is fine for one-off clogs and most branch drains. Hydro jetting is what you want when buildup has reached the pipe wall or the line is suffering from recurring problems. Common signs:
- Kitchen drains that re-clog every few months — grease buildup has coated the line and cabling only punches through it.
- Sewer mains with tree-root intrusion — jet nozzles with root-cutting tips clear roots and flush the debris out.
- Older cast-iron stacks with heavy scale narrowing the pipe — jetting restores diameter without replacement.
- Restaurant or commercial kitchen lines with grease buildup. Cable will not solve a grease problem.
- After a sewer camera shows soft buildup, biofilm, or sand/sediment in the line.
- Before relining or pipe-bursting — the line has to be clean before any trenchless repair.
Our hydro jetting process
Hydro jetting is powerful, which means it has to be done by a tech who reads the line before turning the pressure up. Our sequence:
- 1
Pre-jet camera inspection
We run a sewer camera first to confirm jetting is the right tool, identify any structural damage (cracks, bellies, offsets), and choose the correct nozzle for what's in the line.
- 2
Setup & cleanout access
We protect floors and surrounding fixtures, locate the proper cleanout, and stage the jetter so we can work the line in both directions when needed.
- 3
Calibrated pressure
Older cast iron and clay tile do not get the same pressure as modern PVC. We dial pressure and nozzle type to the pipe material — strong enough to clean, gentle enough not to damage.
- 4
Forward and reverse passes
Reverse jets pull the nozzle through the line while flushing debris back toward the cleanout. Multiple passes ensure the pipe wall is scoured, not just the centerline.
- 5
Verification & report
A second camera pass confirms the line is clean end-to-end. We share the footage with you and document any structural findings you should plan for.
What hydro jetting costs in North Atlanta
Hydro jetting costs more than basic cable cleaning because it requires more equipment, more setup, and a tech trained to use it. Pricing depends on:
- Line length and diameter — longer sewer mains take more time and water.
- Whether a pre- and post-jet camera inspection is bundled (we recommend yes on every job).
- Type of buildup — grease, roots and scale each require different nozzles and passes.
- Access — accessible exterior cleanout vs. roof-vent access changes setup time significantly.
- Whether the line needs spot repair before jetting can safely proceed.
- Time of day for emergency calls.
Why North Atlanta homes need jetting more often than you'd think
North Atlanta is a patchwork of housing stock and soil conditions, and that drives a lot of plumbing decisions. Subdivisions built in the 1990s and early 2000s across Canton, Woodstock and Holly Springs typically run builder-grade PVC and CPVC that's now reaching end-of-life on fittings and shutoffs. Older homes in Marietta, Roswell and Kennesaw still have cast-iron drains and copper supply that scale up and pinhole. Newer construction in Acworth, Ball Ground and Cumming sits on red clay that shifts seasonally and stresses underground lines.
We work in this market every day, so we know which neighborhoods have shared sewer easements, which water utilities require a permit pull, and which inspectors want to see specific fittings. That local knowledge shortens the job and keeps it code-correct the first time.
Need service in a specific area? See our pages for Canton, Woodstock, Holly Springs, Acworth, Kennesaw, Marietta, Roswell and more on our service areas page.
Frequently asked questions
Will hydro jetting damage my pipes?
Not when it's done correctly. We adjust pressure based on pipe material and condition. Older cast-iron with severe corrosion or clay tile with cracks may need a spot repair before jetting — that's why we always camera the line first.
Hydro jetting vs. cable cleaning — which do I need?
Cable is for clearing a clog. Jetting is for cleaning the pipe. If the same line clogs repeatedly, or your camera shows wall buildup, jetting is what actually solves it.
Can hydro jetting cut tree roots?
Yes — root-cutting nozzles handle small to moderate root intrusion and flush the debris out. Severe root damage usually means the line has cracked joints that need trenchless repair afterward.
How often should sewer lines be jetted?
Most homes never need it. Houses with mature trees over the sewer line, or kitchens that send a lot of grease down the drain, often benefit from preventive jetting every 18–24 months.
Need it fixed today?
Same-day service across North Atlanta. Call now or request a quote online.